Ottz Technic
Engineering Science Information Technology
Materials
Mechanical
Marine
Analytical Chemistry Electronics
Books about Mechanical Engineering
For the Mechanical Engineering Industry - Hundreds of Mechanical Engineering Books! Mechanical Engineering Books
Mechanical Engineering Books
Mechanical Engineering Books
Mechanical Engineering Books

Mechanical Engineering Books



Record 121 to 160
First Page Previous Page Next Page Last Page
Alberts, T. E. and American Society of Mechanical Engineers. Dynamic Systems and Control Division. (1995). Proceedings of the ASME Dynamic Systems and Control Division: presented at the 1995 ASME International Mechanical Engineering Congress and Exposition, November 12-17, 1995, San Francisco, California. New York, American Society of Mechanical Engineers.

Albu Austen, H. (1962). The Young Man's Guide to Mechanical Engineering, etc. [With plates.]. London, Hamish Hamilton.

Albu, A. (1962). The young man's guide to mechanical engineering. London, H. Hamilton, [c1962].

Al-Chalabi, A. A. J. (1982). Yield, flow and creep behaviour of powdered steel under combined stress: 267 leaves, 8 leaves of plates.

Alden, G. I. (1877). Notes on Rankine's Applied mechanics. Hartford, Press of the Case, Lockwood & Brainard company.

Aldoory, M. K. (1983). The influence of inlet port design on air motion in internal combustion engine cylinders: 312 leaves, 5 leaves of plates.

Ale Ben, J. M. and D. American Society of Mechanical Engineers Safety Engineering and Risk Analysis, Eds. (2002). Safety engineering and risk analysis 2002.

Ale, B. J. M. and American Society of Mechanical Engineers. Safety Engineering and Risk Analysis Division. (2001). Safety engineering and risk analysis, 2001: presented at the 2001 ASME International Mechanical Engineering Congress and Exposition, November 11-16, 2001, New York, New York. New York, N.Y., American Society of Mechanical Engineers.

Alecio, N. G. (1984). A critical review of radiological aspects of siting of nuclear installations: 378 leaves.

Alefeld, G. and R. Radermacher (1993). Heat conversion systems. Boca Raton; London, CRC Press.

Aleksander, I. (1983). Artificial vision for robots. London, Kogan Page.

Aleksander, I. (1985). Computing techniques for robots. London, Kogan Page.

Aleksandrov, L. I. (1961). Detali mashin: laboratornye raboty.

Alekseev, N. N. and V. P. Puzanova (1948). Razmery i dopuski v mashinostroenii.

Alexander, J. M. (1980). Design, a continuing challenge to the mechanical engineer. Swansea, University College of Swansea.

Alexander, J. M. and B. A. Lengyel (1971). Hydrostatic extrusion. London, Mills and Boon.

Alexander, J. M., R. C. Brewer, et al. (1987). Manufacturing technology. Chichester; New York, Ellis Horwood: Wiley.

Alexander, N. A. (1990). Computational algorithms for the global stability analysis of driven oscillators.

Alexandre, D., A. N. E. Division, et al., Eds. (1993). Nuclear waste management and environmental remediation: 4th Biennial international conference: Papers, ASME.

Alexandropoulos, S. (1996). An experimental investigation of the static and dynamic behaviour of masonry assemblages using small scale models.

Alexandrou, A. N. (2001). Principles of fluid mechanics. Upper Saddle River, N.J.; London, Prentice Hall: Prentice-Hall International.

Al-Faddagh, K. D. (1983). Influence of state of stress on creep failure: 275 leaves, 7 leaves of plates.

Al-Habib, S. M. H. (1990). Transient elasto-plastic response of pulse loaded beams.

Al-Hajeri, A.-R. R. (1995). Sanctions in public works contracts.

Al-Hassani, H. M. (1978). Behaviour of axially restrained concrete slabs.

Al-Hussaini, A. A. (1983). The dynamic response of structures subject to moving loads: 310 leaves.

Ali, S. S. (1981). Flow in a turbulent air jet laden with solid particles: 332 leaves, 5 leaves of plates.

Aliabadi, M. H., C. A. Brebbia, et al. (1993). Contact mechanics: computational techniques: First International Conference on Contact Mechanics 93. Southampton; Boston, MA, Computational Mechanics Publications.

Aliabadi, M. H., M. Denda, et al., Eds. (2001). Advances in boundary element techniques II, Hoggar.

Alijani Moghaddam, H. (1988). Seismic behaviour of brick infilled frames.

Alim, S. (1986). Fuzzy expert systems in civil engineering: 437 leaves.

Al-Janabi, M. A. M. (1991). Theory of cascades for the separation of multi-isotopic mixtures.

Al-Jazari, A. l.-E. i. I. i. i. a.-R. and A. Y. Al-Hassan (1979). Al-jami` bain al-`ilm wal-`amal al-nafi` fi sina`at al-hiyal = A compendium on the theory and practice of the mechanical arts. Aleppo, Institute for the History of Arabic Science, University of Aleppo.

Al-Khafaji, A. W. and J. R. Tooley (1986). Computerized numerical analysis. New York; London, Holt, Rinehart and Wilson.

Al-Khafaji, A. W. and J. R. Tooley (1986). Numerical methods in engineering practice. New York; London, Holt, Rinehart and Winston.

Al-Khazraji, Y. A.-H. (1979). Electromagnetic flowmeters with large electrodes.

All India Solar Energy Working Group. Meeting (7th: 1975: Punjab Agricultural University), K. D. Mannan, et al. (1976). Proceedings of the Seventh Meeting of all India Solar Energy Working Group and Conference on the Utilization of Solar Energy, November 13-14, 1975. Ludhiana, For copies, Dept. of Mechanical Engineering, Punjab Agricultural University.

Allalcha, Z. N. (1990). Regulation of refrigerant flow to evaporators.

Allen David, H., J. W. Ju, et al., Eds. (1994). Damage mechanics in composites 1994: Symposium: International mechanical engineering congress: Papers, ASME.

Allen, J. J. (2005). Micro electro mechanical system design. Boca Raton, Taylor & Francis.


First Page Previous Page Next Page Last Page




Sitemap
Link | Link | Link | Link | Link | Link | Link | Link


powered by FreeFind


Last Modified: 14 October 2005
http://www.ottz.com