Ottz Technic
Engineering Science Information Technology
Materials
Mechanical
Marine
Analytical Chemistry Electronics
Books about Mechanical Engineering
For the Mechanical Engineering Industry - Hundreds of Mechanical Engineering Books! Mechanical Engineering Books
Mechanical Engineering Books
Mechanical Engineering Books
Mechanical Engineering Books

Mechanical Engineering Books



Record 641 to 680
First Page Previous Page Next Page Last Page
Bayer, R. G. (1994). Mechanical wear prediction and prevention. New York, M. Dekker.

Bayer, R. G. (2004). Engineering design for wear. New York, NY; Basel, Marcel Dekker: Taylor & Francis.

Bayer, R. G. (2004). Mechanical wear fundamentals and testing. New York, N.Y., Marcel Dekker.

Bayliss, L. E. (1966). Living control systems. San Francisco, W.H. Freeman; London: Eng. Univ. Press Ltd.

Baynes, K. and F. Pugh (1981). The art of the engineer. Guildford, Surrey, Lutterworth Press.

Baysal, O. and A. F. E. Division, Eds. (1995). CFD for design and optimization: Symposium: International mechanical engineering congress: Papers, ASME.

Baysal, O. and American Society of Mechanical Engineers. Fluids Engineering Division. (1995). CFD for design and optimization: presented at the 1995 ASME International Mechanical Engineering Congress and Exposition, November 12-17, 1995, San Francisco, California. New York, N.Y., American Society of Mechanical Engineers.

BBC Aktiengesellschaft Brown Boveri & Cie. (1987). The Brown Boveri review. Baden, Switzerland, Brown: v.

Beale, S. B. (1993). Fluid flow and heat transfer in tube banks.

Beards, C. F. (1981). Vibration analysis and control system dynamics. Chichester, Horwood.

Beards, C. F. (1983). Structural vibration analysis: modelling, analysis and damping of vibrating structures. Chichester, West Sussex; New York, Ellis Horwood: Halsted Press.

Beards, C. F. (1988). Vibrations and control systems, Ellis Horwood, 1988.

Beasley, D. E., K. D. Cole, et al. (1994). Heat transfer with combined modes: presented at 1994 International Mechanical Engineering Congress and Exposition, Chicago, Illinois, November 6-11, 1994. New York, American Society of Mechanical Engineers.

Beaumont Reginald, A. (1944). Mechanical Testing of Metallic Materials. Second edition. London, Sir I Pitman & Sons.

Beaumont, R. A. (1940). Mechanical testing of metallic materials, with special reference to proof stress. London, Pitman.

Beaver, W. G. (1939). A text book for stationary engineers, first, second, third and fourth class certificates. Philadelphia, David McKay company.

Becker, B. (1959). Mechanical man. New York, Putnam.

Beckermann, C., A. H. T. Division, et al., Eds. (1994). Transport phenomena in solidification: Symposium: International mechanical engineering congress: Papers. ASME -publications- AMD; vol 182, ASME.

Beckermann, C., E. International Mechanical Engineering Congress and, et al. (1994). Transport phenomena in solidification: presented at 1994 international mechanical engineering congress and exposition Chicago, Illinois November 6-11,1994. New York, American Society of Mechanical Engineers.

Beckwith, T. G., N. L. Buck, et al. (1982). Mechanical measurements. Reading, Mass.; London, Addison-Wesley Pub. Co.

Bédard, C. (1983). Non-linear finite element analysis of concrete structures: 296 leaves.

Bedding, N. D. (1989). Determination and behaviour of polynuclear aromatic hydrocarbons during primary sedimentation.

Bedenik, B. (1983). Concrete under triaxial stresses and temperature change: 182 leaves.

Bedford, A. and W. L. Fowler (2001). Engineering mechanics. New Jersey, Prentice Hall.

Bedford, A. and W. L. Fowler (2002). Engineering mechanics: dynamics. Upper Saddle River, N.J.; London, Prentice Hall.

Beech, P. M. (1995). Filmwise condensation of high velocity downward flowing steam on a bundle of horizontal tubes.

Beer, F. P., E. R. Johnston, et al. (1992). Mechanics of materials. New York; London, McGraw-Hill.

Beesley, G. W. (1984). A fluid-film bearing supported elastic rotor: an experimental and theoretical investigation: 331 leaves, 6 leaves of plates.

Beggs, J. S. (1955). Mechanism. New York, McGraw-Hill.

Beggs, J. S. (1966). Advanced mechanism. New York, Macmillan.

Begleris, P. (1987). Three-dimensional flow predictions in motored diesel engines: 477 leaves.

Behrouzi, P. (1989). Performance of multicell, axial-entry cyclones for industrial gas cleaning.

Beitler, S. R. and E. J. Lindahl (1947). Hydraulic machinery. Chicago (Ill.), Irwin-Farnham.

Bejan, A. (1982). Entropy generation through heat and fluid flow. New York; Chichester, Wiley.

Bejan, A. (1988). Advanced engineering thermodynamics. New York; Chichester, John Wiley.

Bejan, A. (1996). Entropy generation minimization: the method of thermodynamic optimization of finite-size systems and finite-time processes. Boca Raton, Fla.; London, CRC Press.

Belgrade University Faculty of Mechanical, E. (1973). Let's get acquainted with Faculty of Mechanical Engineering, University of Belgrade; 1873-1973, University, Faculty of Mechanical Engineering.

Belik, M. Ö. (1982). Symmetric response of ships in regular and irregular waves: 314 leaves.

Bell, A. E. (1970). Mechanical engineering science. London, Cassell.

Bell, A. R. (1922). Railway mechanical engineering: a practical treatise by engineering experts. London, Gresham.


First Page Previous Page Next Page Last Page




Sitemap
Link | Link | Link | Link | Link | Link | Link | Link


powered by FreeFind


Last Modified: 14 October 2005
http://www.ottz.com