Oberg, E. and F. D. Jones (1917). Machinery's encyclopedia; a work of reference covering practical mathematics and mechanics, machine design, machine construction and operation, electrical, gas, hydraulic, and steam power machinery, metallurgy, and kindred subjects in the engineering field. New York, The Industrial Press; [etc.
|
Oberg, E. and F. D. Jones (1942). Machinery's handbook for machine shop and drafting-room: a reference book on machine design and shop practice for the mechanical engineer, draftsman, toolmaker, and machinist. New York, Industrial Press.
|
Oberg, E. and F. D. Jones (1959). Machinery's handbook. New York, Industrial Press: v.
|
Oberg, E. V. (1941). Draftsman's mahtematical manaul. New York, The Industrial press.
|
Oberg, E., F. D. Jones, et al. (1971). Machinery's handbook: a reference book for the mechanical engineer, draftsman, toolmaker and machinist. New York, Industrial Press; Brighton: Machinery Publishing.
|
Oberlies, W. and A. J. d. Gouvêa Neves (1942). Tabelas e fórmulas práticas; electricidade, mecânica. Pôrto, Edições Lopes da Silva.
|
Obert, E. F. (1973). Internal combustion engines and air pollution. New York, Intext Educational Publishers.
|
Obert, E. F. and B. H. Jennings (1968). Internal combustion engines. Scranton, International Textbook Co.
|
Ochiai, S. (1994). Mechanical properties of metallic composites. New York, Marcel Dekker.
|
O'Connell, C. (1985). Directory of microcomputer software for mechanical engineering design. New York, M. Dekker.
|
O'Connell, P. E. (1974). Stochastic modelling of long-term persistence in streamflow sequences.
|
Odgers, J. and D. Kretschmer (1986). Gas turbine fuels and their influence on combustion. Tunbridge Wells, Abacus.
|
Odidi, A. O. O. (1974). The influence of turbulence on the time-mean rate of chemical reactions.
|
O'Donnell, A. T. and J. K. Swales (1978). Regional efficiency in the U.K: mechanical engineering industry. Glasgow, University of Glasgow.
|
Ofori, D. K. (1984). Removal of contaminants from road surface runoff: 265 leaves, 7 leaves of plates.
|
Ogata, K. (1987). Discrete-time control systems. Englewood Cliffs, N.J., Prentice-Hall: Prentice-Hall International.
|
Ogata, K. (1990). Modern control engineering. Englewood Cliffs, N.J., Prentice-Hall International.
|
Ogrodnik, P. J. (1997). Fundamental engineering mechanics. Harlow, Longman.
|
Ogunbekun, O. O. O. (1989). The influence of boundary constraints on the shearing characteristics of particulate solids at extremenly low stress levels.
|
Ogut, A. and American Society of Mechanical Engineers. Fluids Engineering Division. (2002). Proceedings of the ASME Fluids Engineering Division--2002: presented at the 2002 ASME International Mechanical Engineering Congress and Exposition: November 17-22, 2002, New Orleans, Louisiana. New York, NY, American Society of Mechanical Engineers.
|
Ogut, A. and Asme, Eds. (2002). Proceedings of the ASME Fluids Engineering Division 2002, ASME.
|
Oh, C. H. (2001). Hazardous and radioactive waste treatment technologies handbook. Boca Raton, Fla.; London, CRC Press.
|
Oh, J. H. (1991). Estimation of trip matrices from traffic counts: an equilibrium approach.
|
Oh, S. H. (1991). Strategies for end effectors and their use with assembly robots.
|
Ohadi, M. M., A. R. Shekarriz, et al. (1996). Advances in energy efficiency, heat/mass transfer enhancement: presented at the 1996 ASME International Mechanical Engineering Congress and Exposition, November 17-22, 1996, Atlanta, Georgia. New York, N.Y., American Society of Mechanical Engineers.
|
Ohadi, M. M., A. R. Shekarriz, et al., Eds. (1996). Advances in energy efficiency, heat/mass transfer enhancement. ASME -publications- PID; vol 2, ASME.
|
Ohadi, M. M., J. C. Conklin, et al. (1995). Advances in enhanced heat/mass transfer and energy efficiency: presented at the 1995 ASME International Mechanical Engineering Congress and Exposition, November 12-17, 1995, San Francisco, California. New York, N.Y., American Society of Mechanical Engineers.
|
Ohadi, M. M., J. C. Conklin, et al., Eds. (1995). Advances in enhanced heat/mass transfer and energy efficiency: Symposium: International mechanical engineering congress: Papers. ASME -publications- PID; vol 1, ASME.
|
O'Hern Timothy, J. and A. F. E. Division, Eds. (2000). Proceedings of the ASME Fluids Engineering Division: 2000, ASME.
|
O'Hern, T. J. and American Society of Mechanical Engineers. Fluids Engineering Division. (2000). Proceedings of the ASME Fluids Engineering Division, 2000: presented at the 2000 ASME International Mechanical Engineering Congress and Exposition, November 5-10, 2000, Orlando, Florida. New York, N.Y., American Society of Mechanical Engineers.
|
O'Hern, T. J., A. H. T. Division, et al., Eds. (1995). Measurement techniques in multiphase flows: Session: International mechanical engineering congress: Papers. ASME -publication- FED; vol 233, ASME.
|
Ojha, C. S. P. (1993). Modelling of slow sand filters using deep bed filtration theory.
|
Oka, S. and E. J. Anthony (2004). Fluidized bed combustion. New York, N.Y., Marcel Dekker.
|
Okafor, H. O. (1981). Bonded prestressed concrete square slabs subjected to concentrated loading: 337 leaves, 23 leaves of plates.
|
Okhio, C. B. (1982). Swirling flow through conical diffusers: 303 leaves, 9 leaves of plates.
|
Oki, A. A. (1990). Primordial abilities in artificially intelligent systems for civil engineering design.
|
Okishima, K. (1971). Kikai rikigaku.
|
Oklahoma State University Engineering, E. and E. Oklahoma State University School of Mechanical and Aerospace (1987). Applied mechanisms: 10th Conference: Selected papers, The University.
|
Okon, P. (2003). Laser conduction welding of aluminium alloys. Liverpool, Thesis Ph.D.
|
Olama, H. A. L. (1975). Mass-exchange through cold-store doorways.
|
