Oldfield, M. J. (2004). Harmonic excitation of bolted joints. Liverpool, Thesis Ph.D.
|
Oldfield, S. G. (1982). Mass and energy transfer through a poppet exhaust valve of a turbocharged internal combustion engine: 486 leaves, 2 leaves of plates.
|
Olgac, N. and A. D. S. a. C. Division, Eds. (1999). Proceedings of the ASME Dynamic Systems and Control Division: 1999, ASME.
|
Olgac, N. and American Society of Mechanical Engineers. Dynamic Systems and Control Division. (1999). Proceedings of the ASME Dynamic Systems and Control Division, 1999: presented at the 1999 ASME International Mechanical Engineering Congress and Exposition, November 14-19, 1999, Nashville, Tennessee. New York, American Society of Mechanical Engineers.
|
Oliveira, C. R. E. d. (1987). Finite element techniques for multigroup neutron transport calculations with anisotropic scattering: 252 leaves.
|
Oloyede, V. O. A. (1986). Computational studies of materials under cyclic plasticity: 380 leaves.
|
Olson Lorraine, G., S. Saigal, et al., Eds. (1994). Inverse problems in mechanics: Session: International mechanical engineering congress: Papers, ASME.
|
Olson, L. G. and American Society of Mechanical Engineers. Applied Mechanics Division. (1998). ASME Applied Mechanics Division book of abstracts: presented at the 1998 ASME International Mechanical Engineering Congress and Exposition, November 15-20, 1998, Anaheim, California. New York, N.Y., American Society of Mechanical Engineers.
|
Olson, L. G., S. Saigal, et al. (1998). Computational methods for solution of inverse problems in mechanics: presented at the 1998 ASME International Mechanical Engineering Congress and Exposition, November 15-20, 1998, Anaheim, California. New York, N.Y., American Society of Mechanical Engineers.
|
Olukoko, O. A. (1992). Numerical techniques in engineering contact problems with friction.
|
Olver, A. V. (1986). Wear of hard steel in lubricated rolling contact: 262 leaves, [9] leaves of plates.
|
O'Malley, E., S. Scott, et al. (2003). Barriers to energy efficiency: evidence from selected sectors. Dublin, Economic and Social Research Institute.
|
Onabolu, O. A. (1986). Effect of hot crude oil on concrete for offshore storage applications: 309 leaves.
|
O'Neal, D. and American Society of Mechanical Engineers. Advanced Energy Systems Division. (1995). Heat pump and refrigeration systems design, analysis, and applications, 1995: presented at the 1995 ASME International Mechanical Engineering Congress and Exposition, November 12-17, 1995, San Francisco, California. New York, American Society of Mechanical Engineers.
|
O'Neill, M. A. (1992). A kinematic numerical camera model for the SPOT-1 sensor.
|
Onof, C. J. (1992). Stochastic modelling of British rainfall using Poisson processes.
|
Onoufriou, A. (1987). Collapse of damaged ring stiffened cylinders: 346 leaves, [15] leaves of plates.
|
Ontario Council on Graduate Studies. Advisory Committee on Academic Planning. and Council of Ontario Universities. (1973). Perspectives and plans for graduate studies. Toronto, Council of Ontario Universities.
|
Ontario. Board of Examiners of Operating Engineers. (1970). Basic power plant engineering. Toronto, Printed for F. Fogg, printer to the Queen.
|
Onwardi, I. C. (1986). Finite element solutions to elastostatic non-conforming contracts: 388 leaves.
|
Ooi, H. B. (1981). A numerical model for fire resistance of concrete structures: 383 leaves.
|
Oosthuizen, P. H. and D. Naylor (1999). An introduction to convective heat transfer analysis. New York, WCB/McGraw Hill.
|
Oosthuizen, P. H. and W. E. Carscallen (1997). Compressible fluid flow. New York; London, McGraw-Hill.
|
Oosthuizen, P. H., P. G. Kroeger, et al. (1994). Fundamentals of phase change: sublimation and solidification: presented at 1994 International Mechanical Engineering Congress and Exposition, Chicago, Illinois November 6-11, 1994. New York, American Society of Mechanical Engineers.
|
Oosthuizen, P. H., P. G. Kroeger, et al., Eds. (1994). Fundamentals of phase change: sublimation and solidification: Session: International mechanical engineering congress: Papers, ASME.
|
Open University, T. C. T. (1985). Engineering mechanics: solids and fluids. Milton Keynes, Open University Press.
|
Open University. Engineering Materials Course, T. (1981). Engineering materials: an introduction. Technology: a second level course. Milton Keynes, Open University.
|
Open University. Engineering Mechanics: Solids Course, T. (1980). Dynamics. Milton Keynes, Open University Press.
|
Open University. Engineering Mechanics: Solids Course, T. (1980). Engineering mechanics: solids. Milton Keynes, Open University.
|
Open University. Engineering Mechanics: Solids Course, T. (1980). Geometry of mechanisms. Milton Keynes, Open University Press.
|
Open University. Engineering Mechanics: Solids Course, T. (1980). Kinematics. Milton Keynes, Open University Press.
|
Open University. Engineering Mechanics: Solids Course, T. (1980). Structures. Milton Keynes, Open University Press.
|
Open University. Engineering Mechanics: Solids Course, T. (1980). Vibration. Milton Keynes, Open University Press: Open University Press.
|
Open University. Engineering Mechanics: Solids Course, T. (1980). Work, energy, power. Milton Keynes, Open University Press.
|
Open University. Engineering Mechanics: Solids Course, T. (1986). Statics. Milton Keynes, Open University Press.
|
Open University. Introduction to Engineering Mechanics Course, T. (1975). Introduction and mathematics. Milton Keynes, Open University Press.
|
Open University. Introduction to Materials Course, T. (1974). Processing materials - how and why. [Milton Keynes], Open University Press.
|
Open University. Materials: Engineering and Science Course, T. (1994). Materials: engineering and science. Milton Keynes, Open University.
|
Open, U. (1994). Materials, mechanical properties and mechanics. Milton Keynes, Open University Press.
|
Open, U. and T. C. T. Open University (1985). Engineering mechanics: solids and fuels. Milton Keynes, Open University Press.
|
