Ottz Technic
Engineering Science Information Technology
Materials
Mechanical
Marine
Analytical Chemistry Electronics
Books about Mechanical Engineering
For the Mechanical Engineering Industry - Hundreds of Mechanical Engineering Books! Mechanical Engineering Books
Mechanical Engineering Books
Mechanical Engineering Books
Mechanical Engineering Books

Mechanical Engineering Books



Record 5001 to 5040
First Page Previous Page Next Page Last Page
Phelan, R. M. (1957). Fundamentals of mechanical design. New York, McGraw-Hill.

Phelan, R. M. (1967). Dynamics of machinery. New York; London., McGraw-Hill.

Phillips, C. L. and H. T. Nagle (1990). Digital control system analysis and design. London, Prentice-Hall International.

Phillips, J. L. (1994). Indoor air quality of naturally ventilated non-industrial buildings.

Pialucha, T. P. (1992). The reflection coefficient from interface layers in NDT of adhesive joints.

Piazzi Smyth, C. and E. Royal Society of (1869). On intensified gravity in centrifugal governors of driving clocks and steam-engines: by C. Piazzi Smyth. [Glasgow, Printed by W. Mackenzie.

Pickering, C. J. D. (1987). The development of laser speckle metrology for the study of vibration and fluid flow, Original typescript.

Pickford, R., V. International Conference on Developments in, et al. (1985). Papers presented at the International Conference on Developments in Valves & Actuators for Fluid Control, Oxford, England 10-12 September 1985. Cranfield, BHRA.

Pierce Allan, D. (1981). Acoustics: an introduction to its physical principles and applications. New York; London, McGraw-Hill.

Pierce Felix, J. (1968). Microscopic thermodynamics: the kinetic theory and thermodynamics of dilute gas systems. Scranton, Pa, International Textbook Co.

Pierce, A. D. (1981). Acoustics: an introduction to its physical principles and application. New York; London, McGraw-Hill Book Co.

Pierce, F. J. (1968). Microscopic thermodynamics: the kinetic theory and statistical thermodynamics of dilute gas systems. Scranton, International Textbook Co.

Pietrzyk, M. and J. G. Lenard (1991). Thermal-mechanical modelling of the flat rolling process. Berlin; London, Springer.

Pike, A. (1984). I.Mech.E/I.E.E. conditions of contract: a commentary on five I.Mech.E./I.E.E. model forms of general conditions of contract and on the BEAMA contract price adjustment clauses and formulae. London, Sweet & marwell.

Pikoulas, C. (1995). A local grid refinement technique for fluid flow predictions in 3-D.

Pilakoutas, K. (1990). Earthquake resistant design of reinforced concrete walls.

Pilley, A. D. (1983). Simulation of the hyperbar diesel engine turbocharging system: 485 leaves.

Pinarbasi, A. (1995). Flow investigation in centrifugal compressor vaneless and vaned diffusers.

Pinches, M. J. and J. G. Ashby (1988). Power hydraulics. New York; London, Prentice Hall International.

Pink, E. G. and P. Leicester (1977). Current research in polytechnics in mechanical & production engineering: with abstracts. Leicester, Leicester Polytechnic.

Pink, E. G. and P. Leicester (1977). Current research in polytechnics in mechanical and production engineering (with abstracts) 1977. Leicester, Leicester Polytechnic.

Pinnington, R. J. (1982). Vibrational power transmission between sources and substructures, Original typescript.

Pinto Ferreira, C. A. (1882). Guia de mechanica pratica. Lisboa, Imprensa nacional.

Pinto, W. T. (1995). On the dynamics of low tension marine cables.

Pin-Yeh, C., C. Ume, et al., Eds. (1995). Sensors in electronic packaging. ASME -publications- MED; vol 3, ASME.

Piotrowski, J. (1986). Shaft alignment handbook. New York, M. Dekker.

Pipe, J. and J. Moore (2002). What does a wheel do?. London, Aladdin/Watts.

Pippard, A. B. (1983). The physics of vibration. Cambridge, Cambridge University Press.

Pippenger, J. J. (1984). Hydraulic valves and controls: selection and application. New York, N.Y., Dekker.

Piszczek, K., J. Niziol, et al. (1986). Random vibration of mechanical systems. Chichester, Ellis Horwood.

Pitois, E. (1923). Méthodes modernes d'essais à l'usine et d'essais relatifs à l'art de tailler les métaux. Paris, Delagrave.

Pittaras, A. (1993). Adaptive signal prediction with application to ship motions.

Pitts, G. and Seed (1988). System selection: rotary power transmission. [Hatfield?], SEED in association with the Design Council.

Pivovarov, A. M. (1971). Sbornik zadach po mekhanike.

Platt, A. (1987). The life and times of Daniel Gooch. Gloucester, Alan Sutton.

Plint, M. A. (1967). Traction in elastohydrodynamic contacts.

Plint, M. A. and A. Martyr (1995). Engine testing: theory and practice. Oxford; Boston, Butterworth-Heinemann.

Plint, M. A. and L. Böswirth (1986). Mechanical engineering thermodynamics: a laboratory course. London, Griffin.

Plowman, P. and A. Chartered Institute of Management (1987). Accounting in mechanical engineering. London, Chartered Institute of Management Accountants.

Plumb, C. M. (1988). Propulsion system selection for warships: with particular reference to swath design.


First Page Previous Page Next Page Last Page




Sitemap
Link | Link | Link | Link | Link | Link | Link | Link


powered by FreeFind


Last Modified: 14 October 2005
http://www.ottz.com