Ottz Technic
Engineering Science Information Technology
Materials
Mechanical
Marine
Analytical Chemistry Electronics
Books about Mechanical Engineering
For the Mechanical Engineering Industry - Hundreds of Mechanical Engineering Books! Mechanical Engineering Books
Mechanical Engineering Books
Mechanical Engineering Books
Mechanical Engineering Books

Mechanical Engineering Books



Record 6001 to 6040
First Page Previous Page Next Page Last Page
Somerscales Anthony, N. (1914). Mechanical and Marine Engineering Science. Fourth edition. Glasgow; Simpkin, Marshall & Co.: London, James Munro & Co.

Somerscales, A. N. (1909). Mechanical and marine engineering science (essays, problems, demonstrations): specially written as a handbook to the Board of Trade examinations. Glasgow, James Munro & Co. London: Simpkin, Marshall, Hamilton, Kent, & Co., ltd.

Song, B. (1990). Parallelization and optimization procedures for forging modelling.

Soo Hyun, K. (1991). Parameter identification and model based control of direct drive robots.

Soo, S. L., R. W. Besant, et al. (1964). The nature of heat transfer from an enclosed rotating disk. M.E. technical note (University of Illinois. Department of Mechanical Engineering); 9725-3. Urbana, University of Illinois Library.

Soong, T. T., M. C. Costantinou, et al. (1994). Passive and active structural vibration control in civil engineering. Wien, Springer.

Soovere, J. (1984). Dynamic response of acoustically excited stiffened composite honeycomb panels, Original typescript.

Sorensen, H. A. (1951). Gas turbines. New York, Ronald Press Co.

Sorensen, H. A. (1983). Energy conversion systems. New York; Chichester, J. Wiley.

Sorenson, H. W. and E. Institute of Electrical and Electronics, Eds. (1985). Kalman filtering: theory and application. IEEE Press selected reprint series. New York, IEEE Press.

Sors, L. (1967). Plastic mould engineering. Oxford, New York, Pergamon Press.

Sors, L. and S. E. Mitchell (1971). Fatigue design of machine components. Oxford; New York, Pergamon Press.

Sottos, N. R. and American Society of Mechanical Engineers. Materials Division. (1995). Proceedings of the ASME Materials Division: presented at the 1995 ASME International Mechanical Engineering Congress and Exposition, November 12-17, 1995, San Francisco, California. New York, American Society of Mechanical Engineers.

South African Council for Scientific and Industrial Research. National Mechanical Engineering Research Institute. (1976). Reports and publications of the National Mechanical Engineering Research Institute, 1952 to 1975. Pretoria, Council for Scientific and Industrial Research, National Mechanical Engineering Research Institute.

South African Council for Scientific and Industrial, R. (1959). Report of the application of photo-elasticity to ground stress problems. Pretoria, South African Council for Scientific and Industrial Research.

South African Institution of Mechanical Engineers. (1951). The journal of the South African Institution of Mechanical Engineers. Johannesburg, South Africa, The Institution.

South African Institution of Mechanical Engineers. (1955). The South African mechanical engineer. Johannesburg, South African Institution of Mechanical Engineers: v.

South African Institution of Mechanical, E. (1955). Journal of the South African Institution of Mechanical Engineers. Johannesburg, South African Institution of Mechanical Engineers.

South Australian Institute of Technology. Central Library. and A. W. B. Mortimer (1973). Recent conference proceedings in mechanical engineering. [Adelaide], S.A.I.T. Central Library.

South Kensington Museum, a. V. a. A. M. (1901). Catalogue of the mechanical engineering collection, London.

South Kensington Museum, a. V. a. A. M. (1907). Catalogue of the mechanical engineering collection in the Science Division of the Victoria and Albert Museum, South Kensington. With descriptive and historical notes. Part I, London.

South, D. W. and J. R. Mancuso (1994). Mechanical power transmission components. New York, Marcel Dekker.

Southern Regional Council for Further Education. Four Counties' Teaching Research Group. echanical, S. (1963). A suggested scheme of workshop experiments for Part 1 of the C.G.L.I. mechanical engineering technicians' course no.293, Southern Regional Council for Further Education.

Southern Regional Council for Further Education. Motor Vehicle Teaching Method Research, G. (1972). City and Guilds motor vehicle craft studies 381, science experiments. Reading (9 Bath Rd, Reading, Berks. RG1 6HH), Southern Regional Council for Further Education.

Southern, W. R. (2002). The analysis of a generic robotic insertion task. Dublin, Trinity College.

Soutsos, M. N. (1992). Mix design, workability, heat evolution and strength development of high strength concrete.

Souza, M. A. (1982). Vibration characteristics of buckled structures: 354 leaves, 2 leaves of plates.

Souza-Santos, M. L. d. (2004). Solid fuels combustion and gasification: modeling, simulation, and equipment operation. New York, Marcel Dekker.

Spangenberg, E. (1905). Spangenberg's praktische populäre anleitung für ingenieure, heizer, elektriker und maschinisten. St. Louis, G. A. Zeller book co.

Sparkes, M. R. (1997). Automatic CO2 laser beam alignment systems. University of Liverpool, Thesis Ph.D.

Speck James, A. (1997). Mechanical fastening, joining, and assembly. New York, Dekker.

Spencer, H. B. and E. Scottish Centre of Agricultural (1989). Drying rates and dry matter losses in a field trial of grass wilting with frequent mechanical disturbance. Penicuik, Scottish Centre of Agricultural Engineering.

Spencer, N. (1994). An investigation into the resistance characteristics of high speed catamarans in calm water and in waves.

Spikes, H. A. (1972). Physical and chemical absorption in boundary lubrication.

Spindel, J. E. (1961). A study of bridge slabs having no transverse flexural stiffness.

Splawski, B. A. (1981). Finite element methods for neutron transport calculations: 248 leaves.

Spon, E. and E. Spon, Eds. (1881). Supplement to Spons dictionary of engineering, civil, mechanical, military, and naval. London, E. & F.N. Spon.

Spooner, H. J. (1913). Machine design, construction and drawing; a text-book for the use of young engineers. London, New York [etc.], Longmans, Green, and co.

Spring Research, A., A. United Kingdom Atomic Energy, et al. (1974). Helical springs. [London], Oxford University Press for the Design Council, the British Standards Institution and the Council of Engineering Institutions.

Spurr, A. (1980). A computational and experimental study of fully three dimensional transonic flow in turbomachinery, Original typescript.


First Page Previous Page Next Page Last Page




Sitemap
Link | Link | Link | Link | Link | Link | Link | Link


powered by FreeFind


Last Modified: 14 October 2005
http://www.ottz.com