Waid, R. L., D. American Society of Mechanical Engineers. Fluids Engineering, et al. (1973). 1973 Cavitation and Polyphase Flow Forum; presented at [a] Joint Meeting of Fluids Engineering and Applied Mechanics Divisions [of the American Society of Mechanical Engineers], June 20-22, 1973, Georgia Institute of Technology, Atlanta, Georgia. New York, American Society of Mechanical Engineers.
|
Waid, R. L., F. Cavitation and Polyphase Flow, et al. (1976). Cavitation and Polyphase Flow Forum, 1976: [papers] presented at joint meeting of Fluids Engineering Division and Gas Turbine Division of the American Society of Mechanical Engineers, March 21-25, 1976, New Orleans, Louisiana. New York, The Society.
|
Wailes, R. (1979). A source book of windmills and watermills. London, Ward Lock.
|
Wakefield, L. P. (1964). Dimensioning for interchangeability, Pergamon; Macmillan (N.Y.).
|
Walbancke, H. J. (1976). Pore pressure in clay embankments and cuttings.
|
Walker John, D. (1973). [National Certificate Mechanical engineering science.] Certificate mechanical engineering science. (2nd ed.). London, English Universities Press.
|
Walker, A. (1989). Project management in construction. BSP Professional Books, Oxford, BSP Professional Books.
|
Walker, D. J. (1987). Nearshore hydrodynamics and the behaviour of groynes on sandy beaches: 277 leaves, [2] leaves of plates.
|
Walker, E. and P. Periodical (1891). The Engineering Review, a monthly journal for civil, mechanical, and electrical engineers. Edited by H. C. E. Andrée and E. Walker, London.
|
Walker, G. J. (1968). Initial boundary layer measurements on C4 blades in the vortex wind tunnel. Melbourne, Dept. of Supply, Australian Defence Scientific Service, Aeronautical Research Laboratories.
|
Walker, H. (1940). The deflection and profile modification of involute gear teeth.
|
Walker, J. D. (1958). Mechanical engineering science for National certificate. London, English Universities Press.
|
Walker, J. D. (1965). National certificate mechanical engineering science. London, English Universitites Press.
|
Walker, J. D. (1973). Certificate mechanical engineering science. London, English Universities Press.
|
Walker, R. J. (1993). Multi sensor data fusion applied to a class of autonomous land vehicles, Original typescript.
|
Walker, W. (1923). Rukovodstvo po mekhanicheskomu delu.
|
Walker, W. (1938). Der mechaniker: hilfs- und lehrbuch für werkmeister, vorarbeiter, arbeiter und lehrlinge der maschinenbranche, des autogewerbes und verwandter berufsarten sowie für den unterricht an fachschulen, gewerbe- und handwerkerschulen und gewerblichen fortbildungsschulen. Zürich und Leipzig, Morgarten-verlag a.-g.
|
Walker, W. and M. Company Valera (1935). Guía del mecánico práctico. Barcelona, G. Gili.
|
Wall Gordon, C. (1969). Mechanical Engineering Craft Practice, etc. [With illustrations.]. London, Macmillan & Co.
|
Wall, G. C. (1965). Mechanical engineering craft practice: a first year course with exercises, Macmillan.
|
Wall, R. A. and U. Seminar on Mechanical Engineering Information: Provision and (1974). Seminar on Mechanical Engineering Information: Provision and Use held at Loughborough University of Technology, 27-29 March 1974: summary of proceedings: report to OSTI on project SI/G/089. Loughborough, Library, University of Technology.
|
Wall, R. A., I. Great Britain. Office for Scientific and Technical, et al. (1974). Seminar on Mechanical Engineering Information: Provision and Use, held at Loughborough University of Technology 27-29th March 1974, sponsored by the Office for Scientific and Technical Information: summary of proceedings: a report. Loughborough, University of Technology Library.
|
Wall, R. A., I. Great Britain. Office for Scientific and Technical, et al. (1974). Seminar on Mechanical Engineering Information: Provision and Use: held at Loughborough University of Technology 27th-29th March, 1974. summary of proceedings: a report. Loughborough (Loughborough, Leics.), Loughborough University of Technology Library.
|
Wallace, W., T. Terada, et al. (1970). Residual stress analysis in plastically deformed metals of low stacking fault energy. [Ottawa, National Research Council of Canada.
|
Waløen, Å. Ø. (1966). Maskindeler. Trondheim, Tapir.
|
Walsh, R. (2004). Design of carbide heading tooling and an analysis of the forming of a Cotton Picker Spindle. Dublin, Trinity College.
|
Walsh, R. A. (1995). Electromechanical design handbook. New York; London, McGraw-Hill.
|
Walsh, S. J. (1996). Vibrational power transmission in curved and stiffened structures, Original typescript.
|
Walshaw Arthur, C. (1964). Engineering Units and Worked Examples. For students of the mechanical sciences. (Second edition [of "Engineering Units and the Stroud Convention" by F. W. Thorne and A. C. Walshaw].). London & Glasgow, Blackie & Son.
|
Walshaw, A. C. (1964). Engineering units and worked examples for students of the mechanical sciences. London, Blackie.
|
Walshaw, A. C. (1970). SI units and worked examples: for students of the mechanical sciences. [London], Longman.
|
Walshaw, A. C. (1984). Mechanical vibrations with applications. Chichester, Ellis Horwood.
|
Walters, R., D. Institution of Mechanical Engineers. Engineering Manufacturing Industries, et al. (1983). Electric versus hydraulic drives. Bury St. Edmunds, Mechanical Engineering Publications; for the Institution of Mechanical Engineers.
|
Walton, J. N. (1920). Metallic packing, its development, uses and correct application to modern equipment. Chicago, Crane Packing Co.
|
Wan Mohd Akib, W. A. A. (1995). A preliminary determination of a gravimetric geoid in Peninsular Malaysia.
|
Wan, G. T. Y. (1983). Elastohydrodynamic film thickness of water-based hydraulic fluids: 293 leaves, 15 leaves of plates.
|
Wang, C.-S. (1991). A supervisory system for free ranging automated guided vehicles.
|
Wang, H. P., L.-S. Turng, et al. (1997). CAE and intelligent processing of polymeric materials: presented at the 1997 ASME International Mechanical Engineering Congress and Exposition, November 16-21, 1997, Dallas, Texas. New York, ASME.
|
Wang, H. P., L.-S. Turng, et al., Eds. (1997). CAE and intelligent processing of polymeric materials, ASME.
|
Wang, J. and A. Kusiak (2001). Computational intelligence in manufacturing handbook. Boca Raton, Fla.; London, CRC Press.
|
